|
Brand
|
|
Uni-T
|
|
Model
|
UT2062CE
|
|
Bandwidth
|
60MHz_chromatic
|
|
Sampling methods
|
|
Real-time sampling
|
1.0GS/s
|
|
Equivalent Sampling
|
25GS/s
|
|
Average
|
2 n-th power,2 to 256 times optional.
|
|
Enter
|
|
Input Coupling
|
DC _ AC input coupling, ground (DC, AC, GND)
|
|
Input impedance
|
1 ± 2% ΜΩ, and 24 ± 3pF parallel
|
|
probe attenuation coefficient Setting
|
1X, 10X, 100X, 1000X
|
|
Maximum input voltage
|
400V (DC + AC peak, 1ΜΩ input impedance) (10:1 probe attenuation)
|
|
Channel isolation
|
better than 40:1
|
|
Time delay between channels (typical)
|
150ps
|
|
Level
|
|
Waveform interpolation
|
sin(x)/x
|
|
Recording and storage
|
memory depth: 1M samples
|
|
Scan range_S/div_
|
5ns/div _ 50s/div,1-2-5 band (60MHz\80MHz\100MHz)
|
|
Sampling rate and delay time accuracy
|
± 100ppm (any time interval ≥ 1ms)
|
|
Time interval (_ T)
Measurement accuracy (full bandwidth)
|
Single: ± (1 sampling interval +100 ppm × reading +0.6 ns)> 16 Four Means: ± (1 sampling interval +100 ppm × reading +0.4 ns)
|
|
Vertical
|
|
Analog-digital converter (A / D)
|
8-bit resolution, two-channel simultaneous sampling
|
|
Deflection coefficient
|
2mV/div _5V/div(at input BNC Office)
|
|
Displacement range
|
±10div
|
|
analog bandwidth
|
60MHz
|
|
Optional analog bandwidth limitations, typical
|
20MHz
|
|
Low frequency response (AC-coupled,-3dB)
|
≤ 10Hz (in the BNC on)
|
|
Rise time (in the BNC on typical)
|
_5.8ns
|
|
DC gain accuracy
|
2mv/div, 5mv/div hours ± 4% (average sampling or sampling method)
|
|
10mv/div ~ 5v/div Time: ± 3% (average sampling or sampling method)
|
|
DC measurement accuracy (average sampling mode)
|
vertical displacement is zero, and N ≥ 16 _: ± (4% × reading +0.1 div +1 mV); vertical deflection coefficient ≥ 5mV/div; N ≥ 16 _: ± [ 3% × (reading + vertical displacement of the reading) + (1% × vertical displacement of the reading)] +0.2 div) vertical deflection coefficient increases from 2mV/div to 200mV/div 2mV; vertical deflection coefficient 500mV/div to 5V/div plus 50mV .
|
|
Voltage difference (ΔV) measurement accuracy (average sample method)
|
in the same settings and environmental conditions, through to the capture of ≥ 16 waveforms averaged waveform office after the voltage difference between two points (ΔV): ± (3% × reading +0.05 div)
|
|
Trigger
|
|
Trigger sensitivity
|
DC ~ 10MHz 0.5div 10MHz ~ limit the bandwidth 1div
|
|
Trigger level range
|
internal
|
from the screen center within ± 10div
|
|
EXT
|
±1.6V
|
|
EXT/5
|
±8V
|
|
Trigger level accuracy (typical) accuracy for the rise and fall times ≥ 20ns signal
|
internal
|
± (0.3div × V / div) (from the screen center within ± 4div)
|
|
EXT
|
± (6% setting +40 mV)
|
|
EXT/5
|
|
|
± (6% setting +200 mV)
|
|
Pre-trigger capability
|
normal mode / scan mode, pre-trigger / delay trigger, adjustable pre-trigger depth
|
|
Release inhibiting range
|
100ns-1.5s
|
|
Set the level to 50% (typical)
|
input signal frequency ≥ 50Hz operation under
|
|
Edge-triggered
|
|
Edge type
|
up, down
|
|
Trigger pulse width
|
|
Trigger mode
|
(greater than, less than, equal to) is pulse width, (greater than, less than, equal to) the negative pulse width
|
|
Pulse width
|
20ns-10s
|
|
Video Trigger
|
|
Trigger sensitivity
|
internal
|
2div peak value
|
|
(Video trigger, typical)
|
EXT
|
400mV
|
|
|
EXT/5
|
2V
|
|
Signal format and line / field
Frequency (Video Trigger Type)
|
supports standard NTSC and PAL, lines range is 1-525 (NTSC) and 1-625 (PAL)
|
|
Alternate trigger
|
|
CH1 trigger
|
edge, pulse width, video
|
|
CH2 trigger
|
edge, pulse width, video
|
|
Measure
|
|
Cursor
|
manual mode
|
voltage difference between cursors (ΔV), the time difference between cursors (ΔT), ΔT the countdown (Hz) (1/ΔT)
|
|
Tracking mode
|
Tracking mode voltage waveform point and time value
|
|
Automatic measurement
|
peak, amplitude, maximum, minimum, top value, bottom value, average, RMS value, overshoot, pre-washed, frequency, period, rise time, fall time, positive pulse width, negative pulse width, positive duty cycle, negative duty cycle, delay 1 -> 2 (up), delay 1 -> 2 (down) measurement
|
|
Mathematical operations
|
add, subtract, multiply, divide, RP
|
|
Storage Wave
|
10 waveforms, 10 types of settings
|
|
FFT
|
Window
|
Hanning,Hamming,Blackman,Rectangular
|
|
Sampling points
|
1024 points
|
|
Lissajous Figures
|
phase
|
±3 degrees
|
|
Display
|
|
Display Type
|
diagonal of 145 mm (5.7 inches) LCD display
|
|
Display resolution (Display)
|
?320 levels × RGB × 240 vertical pixels (color)
|
|
Display Color
|
chromatic
|
|
Display contrast
|
adjustable
|
|
Backlight intensity (typical)
|
300nit
|
|
Display language
|
Chinese Simplified, Chinese Traditional, English
|
|
Probe Compensator Output
|
|
Output voltage (typical)
|
about 3V, peak - peak load ≥ 1MΩ
|
|
Frequency (typical)
|
1kHz
|
|
Interface functions
|
|
Standard
|
1 USB (D); 1 _ USB (H); 1 _ RS-232C
|
|
Optional
|
GPIB and LAN
|
|
Power supply
|
|
Supply voltage
|
100-240VACRMS 45Hz to 440Hz, CAT II
|
|
Power consumption
|
less than 30VA
|
|
Fuse
|
2A, T stage, 250V
|
|
Environment
|
|
Temperature
|
Operating: 0 _ ~ +40 _
|
|
Non-operating: -20 _ ~ +60 _
|
|
cooling
|
Convection
|
|
Humidity
|
+10 _ ~ +30 _: ≤ 95% ± 5% RH,
|
|
+30 _ ~ +40 _: ≤ 75% ± 5% RH
|
|
high
|
3,000 meters operation
|
|
Non-operating 15,000 m
|
|
Non-operating 15,000 m
|
|
Dimensions
|
320mm (W) × 150mm (high) × 130mm (D)
|
|
Weight (Net)
|
excluding packaging
|
2.5kg
|
|
including packaging
|
4.0 kg
|
|
IP protection
|
IP2X
|
